A chromalloy steel, hand-forged, angle piton with a ring attached through a hole in the top portion to thread a carabiner or rope through. “LONGWARE” is engraved on the outside middle.
A chromalloy steel, hand-forged, angle piton with a ring attached through a hole in the top portion to thread a carabiner or rope through. “LONGWARE” is engraved on the outside middle.
A chromalloy steel, hand-forged, angle piton with a ring attached through a hole in the top portion to thread a carabiner or rope through. “HG” engraved on the inside along with “STUBAI AUSTRIA”
A chromalloy steel, hand-forged, angle piton with a ring attached through a hole in the top portion to thread a carabiner or rope through. “HG” engraved on the inside along with “STUBAI AUSTRIA”
A carabiner with three pitons attached:(a) an aluminum D-ring carabiner (11.0X5.0cm wide) with non-locking gate mechanism on the gate; on one side engraved “H” and then “P. ALLAIN 1600 Kg” in raised block lettering,“G”, on opposite side in raised lettering, on the other “BREVETTE S G D G”.(b) a chr…
A carabiner with three pitons attached:(a) an aluminum D-ring carabiner (11.0X5.0cm wide) with non-locking gate mechanism on the gate; on one side engraved “H” and then “P. ALLAIN 1600 Kg” in raised block lettering,“G”, on opposite side in raised lettering, on the other “BREVETTE S G D G”.(b) a chromalloy steel, hand-forged, angle piton with a round hole at one end. Stamped on both sides is a diamond with a “C” in the middle.(c) A chromalloy steel, hand-forged, angle piton with a round hole at one end”AG” stamped on the inside.(d) A chromalloy steel, hand-forged, short, angle piton with a round hole at one end.
A reversible (green one side and beige on the other), hooded, pullover jacket with diagonal pocket openings above the waist on both sides. The hood has a corded cotton drawstring threaded through to loosen or tighten and below there is an opening with three buttons at the neck. There are two slit p…
A reversible (green one side and beige on the other), hooded, pullover jacket with diagonal pocket openings above the waist on both sides. The hood has a corded cotton drawstring threaded through to loosen or tighten and below there is an opening with three buttons at the neck. There are two slit pocket opening with buttons to open and close, and a cord threaded through the bottom of the jacket to pull through for tightening. The cuffs have a flap with a button and hole to tighten around the wrists.
Canvas bag with leather bottom and shoulder straps, grommet and string closure and metal zipper opening on side, bottom has zipper opening, shoulder straps bound on metal D-ring which is attached to back by a leather patch
Canvas bag with leather bottom and shoulder straps, grommet and string closure and metal zipper opening on side, bottom has zipper opening, shoulder straps bound on metal D-ring which is attached to back by a leather patch
A tanned leather, tool holder that attaches to a belt; used for mountaineering. There are four rivetted holes, which keeps the pieces of leather together, creating an opening to slip a belt through. There is an etched mountain on the front with a climbing tool in front of it.
A tanned leather, tool holder that attaches to a belt; used for mountaineering. There are four rivetted holes, which keeps the pieces of leather together, creating an opening to slip a belt through. There is an etched mountain on the front with a climbing tool in front of it.
Four aluminum carabiners linked together, a combination of spring latch loaded closure system: (a) a D-ring aluminum carabiner (10.0x4.5cm high) with non-locking gate mechanism on the gate; on one side engraved “H” and then raised in block lettering “BREVETTE S G D G”, and then “G” engraved, on op…
Four aluminum carabiners linked together, a combination of spring latch loaded closure system: (a) a D-ring aluminum carabiner (10.0x4.5cm high) with non-locking gate mechanism on the gate; on one side engraved “H” and then raised in block lettering “BREVETTE S G D G”, and then “G” engraved, on opposite side in raised lettering, “P. ALLAIN” on the opposite side.(b) a D-ring aluminum carabiner (10.5x5.0cm high) with non-locking gate mechanism; on one side engraved “H” and then in raised block lettering “BREVETTE S G D G”, and then “G”, on opposite side in raised lettering, “P. ALLAIN 1600 Kg” on the opposite side.(c) An oval-shaped aluminum carabiner (10.0x5.0cm high) with non-locking gate mechanism; “BEDAYN CALIFORNIA” engraved on side.(d) a D-ring aluminum carabiner (11.5.x6.0cm high) with a screw-locking ring mechanism on the gate; on one side engraved “H G”