Air meter enclosed in circular shallow brass case covered with glass, and standing on three brass legs (3.5 cm) attached to a solid brass disk stand of the same size. Brass ring attached perpendicular to side of the meter case by two thin metal arms, contains wind vane with eight small square sails…
Air meter enclosed in circular shallow brass case covered with glass, and standing on three brass legs (3.5 cm) attached to a solid brass disk stand of the same size. Brass ring attached perpendicular to side of the meter case by two thin metal arms, contains wind vane with eight small square sails attached to centre by small metal arms. Face dial measured around perimeter with numbers from 0-90 has small circular dial at top with numbers from 0-9 and the letters "HDS" just above central pivot of small thin needle. Dial reads "Air meter to 1000 feet/No 508". Bottom of solid brass base has screw hole at centre to hold screw mount which is brass finger screw with black painted brass tube attached to top. Lever on side of meter halts needle. Box, plain square wooden box with brass hinges for lid is fitted with small blocks of wood to hold air meter securely in place. Mounting screw slips over arm of piece of wood fastened to lid. Paper label inside lid reads, "Correction for Air Meter No. 508/. Add 30 per minute to the observed reading of the Air Meter. Note. Each instrument is now regulated so as to reduce the correction to a constant quantity per minute, which must be added as in the example given.". Small brass latch hook closes lid.
Large metal amplifying horn from phonograph. Flared shape in eleven sections. Blue paint worn off in many areas. Small red label reads: “‘Rex’ TRADEMARK STANDARD AMPLIFYING HORN. THE BEST FOR TONE. R.S.W. & S.”
Large metal amplifying horn from phonograph. Flared shape in eleven sections. Blue paint worn off in many areas. Small red label reads: “‘Rex’ TRADEMARK STANDARD AMPLIFYING HORN. THE BEST FOR TONE. R.S.W. & S.”
A pair of three-legged andirons. Each andiron has a large, spool like, brass ornament topped with a large ball. This decoration sits on two curved solid brass legs. The third leg is attached behind the first two by a a curved, brass covered, horizontal iron bar. This third leg is topped by a s…
A pair of three-legged andirons. Each andiron has a large, spool like, brass ornament topped with a large ball. This decoration sits on two curved solid brass legs. The third leg is attached behind the first two by a a curved, brass covered, horizontal iron bar. This third leg is topped by a smaller brass knob. The bar attching the third leg continues straight back and bends at a right angle down to form another leg and forms the section that supports logs. The knobs unscrew from the legs and each andiron breaks down.
Wall type aneroid barometer in a brass casing with three brackets for screw mounting, its range is 710 to 790 millimeters. It’s manufactured for the Phillipine Islands and all the surface information is in Spanish. The longer of the two brass needles under the glass is the pressure indicatior and …
Wall type aneroid barometer in a brass casing with three brackets for screw mounting, its range is 710 to 790 millimeters. It’s manufactured for the Phillipine Islands and all the surface information is in Spanish. The longer of the two brass needles under the glass is the pressure indicatior and the shorter of the needles is the setting which can be varied manually for purposes of comparison.
A stylized dragon carved from white onyx. The dragon’s body is flat and slightly arched over a round disk base with a dragon's head at one end looking back over the body. There is an ornate raised relief carving on the body. The base is marked with (Chinese?) characters inside a square.
A stylized dragon carved from white onyx. The dragon’s body is flat and slightly arched over a round disk base with a dragon's head at one end looking back over the body. There is an ornate raised relief carving on the body. The base is marked with (Chinese?) characters inside a square.
Bamboo musical instrument made of two hollow bamboo tubes suspended on split bamboo frame of three thin upright sticks supported in holes cut in hollow bamboo tube at bottom. Two flat pieces of bamboo are secured crosswise into the split uprights and each holds one of the bamboo tubes which are hun…
Bamboo musical instrument made of two hollow bamboo tubes suspended on split bamboo frame of three thin upright sticks supported in holes cut in hollow bamboo tube at bottom. Two flat pieces of bamboo are secured crosswise into the split uprights and each holds one of the bamboo tubes which are hung on them by a semicircular hole which fits into a notch on the crosspiece, half of the upper part of these tubes have been cut away lengthwise and at their bottom two small legs have been carved which fit into wells cut in the bamboo tube at the bottom. When the instrument is held by one of the uprights and shaken, the hollow bamboo clappers strike the sides of this well and make a musical sound.
A white filigree lace antimacassar that has a straight edge across the top with sharp corners and is rounded on the bottom corners. A solid border is scalloped along the rounded edges. The border encloses a wide band of openwork lace containing a diamond shape pattern of thick dots around a solid…
A white filigree lace antimacassar that has a straight edge across the top with sharp corners and is rounded on the bottom corners. A solid border is scalloped along the rounded edges. The border encloses a wide band of openwork lace containing a diamond shape pattern of thick dots around a solid rectangular centre with openwork bar across a repeating diamond pattern.