A long black academic gown with long wide pointed sleeves gathered at the shoulders. The gown opens down the length of the gown front, with a wide panel on either side, and snaps to fasten at the top creating a V-neck. The back of the gown is gathered between the shoulders with a square 'collar' …
A long black academic gown with long wide pointed sleeves gathered at the shoulders. The gown opens down the length of the gown front, with a wide panel on either side, and snaps to fasten at the top creating a V-neck. The back of the gown is gathered between the shoulders with a square 'collar' at the yoke and a line of twisted cording down centre that buttons at the bottom of the yoke. The monogram “P.A.M.” is sewn on a label at the neck. There is also a manufacturer’s label at the neck.
A gold-coloured academic gown gathered at the yoke and sleeves. The gown has a wide curving neck and front opening that are banded with black satin. There are three black satin bands along edges of the wide, long, pointed sleeves. The gown fastens at the front of the neck with hooks and a narro…
A gold-coloured academic gown gathered at the yoke and sleeves. The gown has a wide curving neck and front opening that are banded with black satin. There are three black satin bands along edges of the wide, long, pointed sleeves. The gown fastens at the front of the neck with hooks and a narrow ribbon tie.
A black academic hood that has a sleeve shape at the end. The deep hood is lined with orange silk and black silk in wide bands. The hood is edged in light grey velvet which forms a strap to pass over the shoulders and rest on the chest.
A black academic hood that has a sleeve shape at the end. The deep hood is lined with orange silk and black silk in wide bands. The hood is edged in light grey velvet which forms a strap to pass over the shoulders and rest on the chest.
Air meter enclosed in circular shallow brass case covered with glass, and standing on three brass legs (3.5 cm) attached to a solid brass disk stand of the same size. Brass ring attached perpendicular to side of the meter case by two thin metal arms, contains wind vane with eight small square sails…
Air meter enclosed in circular shallow brass case covered with glass, and standing on three brass legs (3.5 cm) attached to a solid brass disk stand of the same size. Brass ring attached perpendicular to side of the meter case by two thin metal arms, contains wind vane with eight small square sails attached to centre by small metal arms. Face dial measured around perimeter with numbers from 0-90 has small circular dial at top with numbers from 0-9 and the letters "HDS" just above central pivot of small thin needle. Dial reads "Air meter to 1000 feet/No 508". Bottom of solid brass base has screw hole at centre to hold screw mount which is brass finger screw with black painted brass tube attached to top. Lever on side of meter halts needle. Box, plain square wooden box with brass hinges for lid is fitted with small blocks of wood to hold air meter securely in place. Mounting screw slips over arm of piece of wood fastened to lid. Paper label inside lid reads, "Correction for Air Meter No. 508/. Add 30 per minute to the observed reading of the Air Meter. Note. Each instrument is now regulated so as to reduce the correction to a constant quantity per minute, which must be added as in the example given.". Small brass latch hook closes lid.
Olive green felt alpine hat with hatband made of three strands of gold cord. Broken black feather tucked into hatband. Two labels inside hat: “Made in Austria” & “ORIGINAL Tscher HUT.”
Olive green felt alpine hat with hatband made of three strands of gold cord. Broken black feather tucked into hatband. Two labels inside hat: “Made in Austria” & “ORIGINAL Tscher HUT.”
Large metal amplifying horn from phonograph. Flared shape in eleven sections. Blue paint worn off in many areas. Small red label reads: “‘Rex’ TRADEMARK STANDARD AMPLIFYING HORN. THE BEST FOR TONE. R.S.W. & S.”
Large metal amplifying horn from phonograph. Flared shape in eleven sections. Blue paint worn off in many areas. Small red label reads: “‘Rex’ TRADEMARK STANDARD AMPLIFYING HORN. THE BEST FOR TONE. R.S.W. & S.”
A very thin knife with ebony handle like rifle butt and wooden scabbard wrapped with bands of black cord. (a) dirk, short, narrow, pointed steel blade with reverse curve to sharp shoulder on under side of hilt. Small carved ebony handle shaped like a rifle butt, with carved band of scallops and d…
A very thin knife with ebony handle like rifle butt and wooden scabbard wrapped with bands of black cord. (a) dirk, short, narrow, pointed steel blade with reverse curve to sharp shoulder on under side of hilt. Small carved ebony handle shaped like a rifle butt, with carved band of scallops and diamond shapes around middle. Two decorative notches carved across butt of handle. Note: handle checked along length. (b) scabbard, small, simple and straight, carved of two pieces of wood with triangular opening at mouth. Top carved to curve downward on one side to accommodate shoulder of blade. Girded with four double bands of finely braided cord, evenly spaced along length, and a fifth triple band at top beneath shoulder. Note: top fibre hands loose and slide up and down.
A pair of three-legged andirons. Each andiron has a large, spool like, brass ornament topped with a large ball. This decoration sits on two curved solid brass legs. The third leg is attached behind the first two by a a curved, brass covered, horizontal iron bar. This third leg is topped by a s…
A pair of three-legged andirons. Each andiron has a large, spool like, brass ornament topped with a large ball. This decoration sits on two curved solid brass legs. The third leg is attached behind the first two by a a curved, brass covered, horizontal iron bar. This third leg is topped by a smaller brass knob. The bar attching the third leg continues straight back and bends at a right angle down to form another leg and forms the section that supports logs. The knobs unscrew from the legs and each andiron breaks down.
Wall type aneroid barometer in a brass casing with three brackets for screw mounting, its range is 710 to 790 millimeters. It’s manufactured for the Phillipine Islands and all the surface information is in Spanish. The longer of the two brass needles under the glass is the pressure indicatior and …
Wall type aneroid barometer in a brass casing with three brackets for screw mounting, its range is 710 to 790 millimeters. It’s manufactured for the Phillipine Islands and all the surface information is in Spanish. The longer of the two brass needles under the glass is the pressure indicatior and the shorter of the needles is the setting which can be varied manually for purposes of comparison.
Two aneroid barometer-altimeters (a & b) labeled: “Keuffel & Esser Co. N.Y. MADE IN ENGLAND. Improved Surveying Aneroid Compensated” Black oxidized finish on the case. Altitude graduation up to 12,000 feet. Leather carrying cases contain comparative pressure test sheet dated 1903 and issued by Keuf…
Two aneroid barometer-altimeters (a & b) labeled: “Keuffel & Esser Co. N.Y. MADE IN ENGLAND. Improved Surveying Aneroid Compensated” Black oxidized finish on the case. Altitude graduation up to 12,000 feet. Leather carrying cases contain comparative pressure test sheet dated 1903 and issued by Keuffel & Esser.